There are a few ways to do this, but the most common is to remove the gas cap and use a siphon hose. Another way is to remove the gas tank and pour the gas out. Whichever method you choose, make sure you have a container to catch the gas.
- Make sure that your motorcycle is turned off and that the engine is cool before beginning this project
- Locate the drain plug on the bottom of the gas tank
- This is typically a small brass or steel plug with a hexagonal head
- Use a wrench to loosen the drain plug and allow the gasoline to begin draining into a container such as an empty milk jug or oil drain pan
- Once the majority of the gasoline has drained out, remove the gas cap from atop the tank to allow any remaining fumes to escape
- Replace both the gas cap and drain plug when finished, and dispose of any excess gasoline properly according to local regulations
How to Drain Gas from Fuel Injected Motorcycle
If you own a fuel injected motorcycle, you know that it’s important to keep the gas tank full. But what do you do when it’s time to change the oil or perform other maintenance? Here’s how to drain gas from your fuel injected motorcycle:
1. Remove the seat and side panels to access the gas tank.
2. Locate the drain plug at the bottom of the tank and remove it with a wrench.
3. Place a pan under the tank and let the gas drain out completely.
Be sure to dispose of the used gasoline properly!
4. Replace the drain plug and reassemble your motorcycle.
Credit: www.youtube.com
How Do I Empty My Motorcycle Gas Tank?
Assuming you need to do this for maintenance or storage:
First, find the valve on your fuel line. It’s usually located near the carburetor or fuel injection system.
Once you’ve found it, turn the valve to the “off” position. This will stop the flow of gas. Next, start up your motorcycle and let it run until it runs out of gas and stalls.
Finally, disconnect the negative battery cable to prevent any sparks. And that’s it! Your motorcycle’s gas tank is now empty.
What is the Easiest Way to Drain a Gas Tank?
The easiest way to drain a gas tank is to siphon the gas out using a hose. First, find a garden hose that is long enough to reach from the gas tank to the ground. Next, put one end of the hose into the gas tank and suck on the other end of the hose until the gas starts flowing.
Once the gas starts flowing, hold onto the end of the hose so it doesn’t fall out and let gravity do its job. The gas will flow out of the tank and into your mouth (yuck!), so make sure you have a container handy to catch it in. When you’re finished draining all of the gas, remove the hose and cap off both ends.
Should I Drain Old Gas from Motorcycle?
If you’re storing your motorcycle for the winter, or if it’s been sitting in your garage for a while, you might be wondering whether you should drain the gas. After all, old gas can go bad and clog up your engine.
The good news is that you don’t necessarily need to drain the gas from your motorcycle before storing it.
In fact, there are some benefits to leaving a little bit of gas in the tank. First, it will help keep moisture out of the tank. Second, it will act as a lubricant for the seals and prevent them from drying out.
Of course, there are also some drawbacks to leaving gas in the tank. The biggest one is that if the gas goes bad, it can damage your engine. So if you’re going to store your motorcycle for an extended period of time (more than a few months), it’s probably best to drain the gas.
To do this, simply remove the fuel line from the carburetor or fuel injectors and let the gas run out into a container. Once it’s empty, put freshgas in and start ‘er up!
Is There a Drain Plug on the Fuel Tank?
Most fuel tanks do not have a drain plug. The reason for this is because the fuel tank is usually vented to allow air to enter as the fuel is used. If there was a drain plug, the pressure inside the tank would build up and eventually cause the tank to burst.
Very Easy Way To Empty A Motorcycle Gas Tank
Conclusion
If your motorcycle has been sitting for a while, you may need to drain the gas tank. This is a simple process that only takes a few minutes. First, locate the valve at the bottom of the tank.
This is usually located on the left side of the bike. Next, use a wrench to loosen the valve and allow the gas to drain out into a container. Once the tank is empty, close the valve and replace any parts that were removed.