To safely jump start another car with your Mercedes, first park the Mercedes close to the other car with the engines off. Then, open the hoods of both cars and locate the batteries. On each battery, you will see two metal posts labeled “positive” ( typically red) and “negative” (typically black).
Take the jumper cables and attach one end of the red cable to the positive post on the dead battery, and then do the same with the other end of the red cable to the positive post on your working battery. Next, take one end ofthe black cable and attach it to negative post on your working battery, and then attachthe other end ofthe black cable to any metal ground onthe dead car – notto its negative battery post.
- Park the Mercedes-Benz beside the car with the dead battery
- Make sure both vehicles are turned off and the parking brakes are engaged
- Open the hoods of both cars and locate each battery
- On the Mercedes-Benz, remove the plastic cover from over the battery terminals (if applicable)
- Connect one end of the red/positive jumper cable to the positive terminal on the dead battery
- Then connect the other end of that same cable to the positive terminal on the Mercedes-Benz battery
- Next, take one end ofthe black/negative jumper cable and connect it tothe negative terminal onthe Mercedes-Benz battery
- The final step isto connectthe remainingendof that black/negativecableto an unpaintedmetal surfaceon he car withthedeadbattery—this will helpcomplete themetal circuitand allow fora proper jump start
Can You Jumpstart a Mercedes C Class
If your Mercedes-Benz C-Class won’t start, there are a few things you can do to try and jumpstart it. First, make sure that the battery is properly connected and that the terminals are clean. If the battery is low on power, you can try charging it for a few hours before attempting to jumpstart the car.
If the battery is completely dead, you’ll need to replace it.
Once you’ve checked the battery, locate the jumper cables in your trunk. If you don’t have jumper cables, you can use a booster pack or another car with a working battery.
Attach one end of the positive cable (red) to the positive terminal on your dead battery, and then attach the other end of the positive cable to the working battery. Next, attach one end of the negative cable (black) to the negative terminal on the working battery, and then attach the other end of the negative cable to a metal ground on your car. Make sure that all connections are tight and secure before starting either car.
Once everything is hooked up correctly, start up the working car and let it run for a few minutes. Then try starting your Mercedes-Benz C-Class. If it starts up successfully, disconnect all ofthe cables immediately and take your car for a short driveto help charge upthebattery again .
Credit: www.mercedesbenzofcharleston.com
Where Do Jumper Cables Go on Mercedes?
Jumper cables are an essential part of any roadside emergency kit. But if you’ve ever been in a situation where you needed to use them, you know that it can be a little bit tricky to figure out where they go. If you’re driving a Mercedes, the process is actually quite simple.
Here’s a quick guide to help you out the next time you need to use jumper cables on your Mercedes.
First, locate the battery under the hood. The positive terminal will be labeled with a “+” sign, and the negative terminal will be labeled with a “-” sign.
Next, take the red jumper cable and attach it to the positive terminal on your battery. Then, take the other end of the red cable and attach it to the positive terminal on the donor vehicle’s battery.
Now it’s time to connect the black jumper cable.
First, attach one end of the black cable to the negative terminal on your own vehicle’s battery. Then, take the other end of the black cable and attach it to some sort of metal ground onthe donor vehicle – this could be a bolt onthe frame or engine block. Avoid attaching itto anything that might be painted (like astud), as this could cause sparks whenyou try to start your car.
How Do You Use Jumper Cables on a Mercedes?
Assuming you need to jump start your Mercedes, you would need to:
1. Park the donor vehicle close to the front of your Mercedes, but not so close that the vehicles might touch. Turn off both engines.
2. Open the hoods of both vehicles and locate the batteries. On a Mercedes, the battery is usually located in the front right side of the engine compartment (as you’re looking at it from the front of the car). You’ll see two large black terminal posts on top of the battery – these are where you’ll attach the jumper cables.
3. Make sure that there’s no dirt or corrosion on either set of terminal posts, as this can prevent a good connection from being made. If necessary, clean off any corrosion with a wire brush or similar tool.
4. Attach one end of the RED cable to the POSITIVE (+) post on your dead battery.
Then attach the other end of that same cable to the POSITIVE (+) post on the donor battery.
5 .Attach one end ofthe BLACK cable tothe NEGATIVE (-) post onthe donor battery .
Then attachthe other endofthat samecabletoany exposedmetal partofthe engine blockonyour car(awayfromthebattery). This will help prevent acircuit frombeing completed through sensitive electronic components should something go wrong duringthejumping process .
6 .
Startupdonorvehicleand let itsengine runfor severalminutesbeforeattemptingtostartyour owncar .
7 . Trystartingyour ownvehicle now .
Can You Mess Up Your Car by Jump Starting Another Car?
If you’re jump starting another car, the answer is yes – you can mess up your car. Here’s how:
When you connect the jumper cables to your car and the other car, be sure that the red clamps go on the positive (red or orange) terminals of both batteries, and that the black clamp goes on the negative terminal of the dead battery.
If you accidentally reverse these connections, you’ll actually be sending a charge backwards through the electrical system which can damage sensitive electronic components like alternators and starters.
Additionally, if either battery is old or damaged, jump starting can cause an explosion. So it’s always best to use caution when working with batteries.
How To Jump Start/Charge Mercedes Vehicles
Conclusion
When you have a Mercedes, you can feel confident that you have a quality car. But, what do you do when your battery dies and you need to jump start another car? Here are the steps to follow:
1. Open the hood of both cars.
2. Locate the batteries.
3. Identify the positive and negative terminals on each battery.
4. Attach the red jumper cable to the positive terminal on one battery, and then attach the other end of the red jumper cable to the positive terminal on the other battery.
5. Attach one end of the black jumper cable to the negative terminal on one battery, and then attach the other end ofthe black jumper cable to an unpainted metal surface on both cars (this will help to ground them).
6. Start up your Mercedes, and let it run for a few minutes before starting upthe other car.