1. Connect a garden hose to the boat’s engine and run the engine until it reaches operating temperature.
2. circulating the antifreeze throughout the engine, raw water pump, and hoses. Open all seacocks and valves to allow
3. Once the engine is at operating temperature, turn off the ignition switch and disconnect the negative battery cable.
4. Remove the spark plugs and spray a liberal amount of fogging oil into each cylinder through the spark plug hole. This will prevent corrosion during winter storage.
Replace the spark plugs and reconnect the negative battery cable..5
- Drain the engine block by removing the drain plug at the bottom of the engine
- Remove the thermostat and flush the cooling system with fresh water
- Add a marine antifreeze to the cooling system and replace the thermostat
- Change the oil and filter according to your maintenance schedule
- Lubricate all moving parts on the engine including throttle, shifter and control cables, steering components, etc
- Inspect all belts and hoses for cracks or wear and replace as necessary
- Check all fluid levels in the engine including coolant, oil, power steering fluid, etc
- , and top off as needed
How To Winterize a Boat – Mercruiser 3.0 , 5.7 , 4.3 , 4.0 – EASY
Mercruiser Winterizing Manual
It’s that time of year again – time to start thinking about winterizing your Mercruiser engine. While the process may seem daunting, it’s actually quite simple if you follow these steps from the Mercruiser Winterizing Manual.
1. Change the oil and filter.
This is always a good idea before putting your engine into storage, and will help to remove any contaminants that could cause problems during the winter months.
2. Add fuel stabilizer to your gas tank. This will help to keep the fuel fresh and prevent it from breaking down over time.
3. Drain the cooling system. Begin by disconnecting the hose at the raw water pump and running the engine until all of the water has been flushed out. Then, open all of the drains on the engine block, manifolds, and risers to allow all of the remaining water to drain out completely.
Finally, reconnect the hose at the raw water pump and add antifreeze to fill up the system – be sure to use a 50/50 mix of antifreeze and distilled water for best results.
Credit: darsenginerepair.weebly.com
How Much Antifreeze Do I Need to Winterize My 3.0 Mercruiser?
Assuming you have a 3.0L MerCruiser engine, you will need approximately 3 gallons of antifreeze to winterize your engine. Here is a step-by-step guide on how to properly winterize your MerCruiser engine:
1. Start by flushing the entire cooling system with fresh water.
This will help remove any salt, dirt or debris that may be present in the system.
2. Next, add the recommended amount of antifreeze to the system. For a 3.0L engine, this would be approximately 3 gallons.
Make sure to use a high quality marine antifreeze that is designed for use in salt water environments.
3. Once the antifreeze has been added, run the engine for several minutes to allow it to circulate throughout the system.
4. Finally, turn off the engine and disconnect the negative battery terminal to prevent corrosion while your boat is stored for the winter months ahead.
Where are the Drain Plugs on a 3.0 Mercruiser?
If you’re looking for the drain plugs on a 3.0 MerCruiser, you’ll find them on the back of the engine. There are two of them, and they’re located just behind the propeller shaft. To access them, you’ll need to remove the propeller and then unscrew the plugs.
How Do You Winterize a Mercruiser Inboard?
If you have a MerCruiser inboard engine, winterizing it is an important part of maintaining it. Here are the steps you need to take to winterize your engine:
1. Change the oil and filter.
This will help remove any water or other contaminants that may have gotten into the engine during the summer months.
2. Add fuel stabilizer to your gas tank. This will help keep the gas from going bad over the winter months.
3. Drain the cooling system and add antifreeze. This will prevent the water in the cooling system from freezing and damaging the engine.
4. Remove the battery and store it in a warm, dry place.
Batteries can freeze and crack if they are left in cold temperatures for too long.
5. Cover the engine with a tarp or other protective covering.
What Do I Need to Winterize My Mercruiser?
Assuming you have a MerCruiser inboard engine and are putting it into winter storage:
1. Add fresh fuel to the tank and treat with a stabilizer. This will help keep the fuel fresh and prevent any condensation from forming inside the tank.
2. Change the oil and filter. Old, dirty oil can cause corrosion and damage during storage.
3. Remove the spark plugs and spray fogging oil into each cylinder.
This will help protect the cylinders from corrosion while they’re not being used.
4. Disconnect the battery and store it in a cool, dry place. Batteries can self-discharge during storage, so it’s best to keep them disconnected until you’re ready to use them again.
5. Flush out the cooling system with fresh water and antifreeze (or just antifreeze if you’re in a particularly cold climate). This will help prevent any corrosion or freezing that could damage your engine during storage.
Conclusion
If you have a 3.0 Mercruiser, it’s important to winterize it properly so that it will be ready to go when spring comes. Here are the steps you need to take:
1. Change the oil and filter.
This will help remove any water that may have gotten into the engine during the summer months.
2. Drain the cooling system and add fresh antifreeze. Be sure to use a 50/50 mix of ethylene glycol and distilled water.
3. Remove the spark plugs and spray fogging oil into each cylinder. This will help prevent corrosion over the winter months.
4. Disconnect the battery and store it in a cool, dry place.
This will help extend its life over the winter months.