If you own a Chevy Silverado, you may have experienced problems with your windshield wipers. The wipers may stop working altogether, or they may work intermittently. You may also notice that the blades are not making full contact with the windshield.
This can be a frustrating problem, especially if it happens when you need them the most.
If you own a Chevrolet Silverado, you may have experienced a problem with your windshield wipers. The wipers may stop working or they may only work intermittently. This can be a real problem, especially if you live in an area where it rains frequently.
There are several possible causes for this problem. One is that the wiper motor may be failing. Another possibility is that the wiper linkage could be damaged or broken.
If your Silverado’s windshield wipers are not working properly, take it to a qualified mechanic or dealership service department and have them diagnose and fix the problem. Don’t wait until it’s raining to find out that your wipers don’t work!
Troubleshooting Windshield Wiper Problems
If your windshield wipers aren’t working properly, there are a few things you can do to troubleshoot the problem. First, check to see if the blades are dirty or damaged. If they are, clean or replace them.
Next, make sure that the wipers are properly attached to the arms. If they’re not, they won’t work correctly. Finally, check the fuse to see if it’s blown.
If it is, replace it with a new one. With these simple steps, you should be able to fix most windshield wiper problems.
How Do You Reset Windshield Wipers?
If your windshield wipers are leaving streaks on your windshield or they’re not functioning properly, it’s probably time to reset them. Here’s how to do it:
1. First, clean the blades with a rag soaked in vinegar.
This will remove any built-up grime that could be causing the streaks.
2. Next, open the hood and locate the wiper motor. On most vehicles, the motor is located behind the passenger-side headlight.
3. Disconnect the negative battery cable from the terminal. This will prevent electrical shocks while you’re working on the wipers.
4. Locate the two small metal tabs on either side of the wiper motor.
These tabs control the up and down movement of the wipers.
5. Use a flathead screwdriver to gently pry each tab up about 1/4 inch. Be careful not to damage or bend the tabs too much—you’ll need them to function properly when you reassemble everything later on!
6. With both tabs pried up, pull outwards on each arm of the wiper until it comes free from its socket in the motor housing (see image below).
How Do You Know If Your Wiper Relay is Bad?
If your windshield wipers are not working properly, it is likely that the wiper relay is bad. There are a few ways to tell if this is the case. First, check to see if the fuse for the wipers is blown.
If it is, then replace it and see if that fixes the problem. If not, then take a look at the wiper motor itself. If there is any corrosion or damage to the wires leading to it, then chances are that the relay is bad and will need to be replaced.
How Do I Troubleshoot My Windshield Wipers?
If your windshield wipers are not working properly, there are a few things you can do to troubleshoot the problem. First, check to see if the wipers are turned on. If they are, then check to see if the blades are dirty or damaged.
If they are, then replace them with new ones.
If the wipers are turned on and the blades are clean and undamaged, then check to see if there is power getting to the wiper motor. If there is no power, then check the fuse box for a blown fuse.
If there is power but the motor isn’t working, then it may be burned out and will need to be replaced.
Why is One Windshield Wiper Working And Not the Other?
If you’ve ever found yourself driving in the rain with only one windshield wiper working, you know how frustrating it can be. There are a few reasons why this might happen, and fortunately, they’re all relatively easy to fix.
The most common reason for one wiper to stop working is a blown fuse.
Fuses power your wipers, so if one has blown, the corresponding wiper will stop working. To check if this is the problem, locate your vehicle’s fuse box and look for a blown fuse. If you find one, simply replace it with a new fuse of the same amperage.
Another possibility is that the wiper motor itself has burned out. This is less common than a blown fuse, but it does happen from time to time. If you suspect that the motor is the problem, you’ll need to take your vehicle to a mechanic or dealership for repairs.
It’s also possible that something is blocking one of your wipers from moving freely. This could be anything from dirt and debris to ice and snow build-up. If you think this might be the problem, try cleaning off your windshield and wipers with soap and water or de-icer spray.
You may also need to remove any physical obstructions like leaves or sticks that could be preventing movement.
Hopefully this information helps you get to the bottom of why one of your windshield wipers isn’t working properly!
Conclusion
Recently, many Chevrolet Silverado owners have been having problems with their windshield wipers. The wipers will sometimes stop working or work intermittently, and the problem seems to be getting worse. GM is aware of the problem and has issued a service bulletin, but so far no recall has been issued.
In the meantime, some owners are having to replace their windshield wipers more frequently, and others are afraid to use them at all in case they get stuck in the middle of a rainstorm.