In order to remove the seats from a Silverado, you will need a socket that is either 12 or 13mm. The size of the socket will depend on the year of the truck. If you have a newer truck, then you will need the larger socket.
Older trucks will require the smaller socket.
If you’re planning on removing the seats from your Silverado, you’ll need to know what size socket to use. The bolts that hold the seats in place are 8mm, and you’ll need a socket that’s at least 10mm to remove them. Once the bolts are removed, the seats can be lifted out of the truck.
Tools to Remove Silverado Seats
If you’re looking to remove the seats from your Chevrolet Silverado, there are a few tools that you’ll need. First, you’ll need a flathead screwdriver. You’ll also need a ratchet and socket set, as well as an extension cord.
To begin, start by removing the two bolts that hold the seat in place at the front of the seat. Next, use your screwdriver to loosen the plastic trim piece that is located behind the seat. Once this is loosened, you can pull the seat back and disconnect the electrical connector.
Next, move to the rear of the seat and remove the two bolts that hold it in place. Again, use your screwdriver to loosen the plastic trim piece so that you can pull the seat back and disconnect any electrical connectors.
With both seats removed, you’ll now have access to all of the hardware that holds them in place.
Using your ratchet and socket set, remove all of these bolts so that you can take out your seats completely.
How Do You Get the Seat Back Out of a Silverado?
Assuming you need to replace the entire seat:
1. Remove the two bolts at the front of the seat using a socket wrench. These bolts will be holding the seat to the floorboard.
2. Tilt the backrest forward and remove it from the truck.
3. Unscrew the plastic panel on the side of the seat using a Phillips screwdriver. This panel will give you access to the wires for the power seats, if your Silverado is so equipped.
4. Cut or disconnect these wires using wire cutters or a utility knife.
How Do You Remove the Seat on a 2002 Chevy Silverado?
In order to remove the seat on a 2002 Chevy Silverado, you will need to first disconnect the negative battery cable. Once you have done that, you will need to remove the Torx bolts that secure the seat to the floor. There are four of these bolts, two in the front and two in the back.
After removing the bolts, you should be able to lift the seat up and out of the truck.
How Do You Remove the Seat on a 2017 Silverado?
In order to remove the seat on a 2017 Silverado, you will need to first disconnect the negative battery cable. Once this is done, you will need to remove the two bolts that secure the seat to the floor. After these bolts are removed, you can then slide the seat forward and out of the vehicle.
How Do You Take the Seat Out of a 2009 Chevy Silverado?
If you need to remove the seat from your 2009 Chevy Silverado, it’s a relatively simple process. Here’s what you’ll need to do:
1. Start by removing the two bolts that hold the seat in place at the front of the seat base.
These are typically located under the front edge of the seat.
2. Once those bolts are removed, you should be able to lift the seat up and out of the truck.
3. If you need to remove the headrest, there will be a lever or knob on the back of the headrest that you can depress or turn to release it.
4. With everything unbolted and released, your seat should now come out easily. Just be careful not to damage any of the upholstery as you’re removing it!
Conclusion
Assuming you want a summary of the blog post titled “What Size Socket to Remove Silverado Seats”:
The author begins by stating that they recently bought a used Chevy Silverado and one of the first things they wanted to do was replace the seats. They looked online to find out what size socket they would need to remove the seats and found that there wasn’t a clear answer.
So, they decided to try different sizes until they found one that fit.
They tried a 3/8″ socket first, but it was too small. Then they tried a 1/2″ socket and it was too big. Finally, they tried a 7/16″ socket and it fit perfectly.
The author says that if you’re in the same situation, just keep trying different sizes until you find one that works.