If your 2014 GMC Terrain won’t start, you may need to jumpstart it. To do this, you will need a set of jumper cables and another vehicle with a working engine. Once you have the supplies, follow these steps:
1) Park the good vehicle close to the Terrain, but do not let the vehicles touch.
2) Open the hoods of both vehicles and locate the batteries.
3) Attach one end of the red (positive) cable to the positive terminal of the dead battery.
4) Attach the other end of the red cable to the positive terminal of the good battery.
5) Attach one end of the black (negative) cable to the negative terminal of the good battery.
6) Finally, attach the other end of black cable to an unpainted metal surface on your Terrain’s engine block away from any moving parts.
7) Start up your good vehicle and let it run for a few minutes before starting your Terrain. If everything is working properly, your Terrain should start right up!
GMC TERRAIN BATTERY REPLACEMENT AND HOW TO JUMP START
How to Charge a Battery on a 2014 Gmc Terrain
If your 2014 GMC Terrain won’t start, one possible cause could be a dead battery. Here’s how to charge it up so you can get back on the road.
First, make sure that your charger is working and plugged into a power outlet.
If it is, then connect the positive (red) lead to the positive terminal on the battery, and the negative (black) lead to either the negative terminal or a metal ground point on the engine block.
Once everything is connected, turn on your charger and let it do its thing. Depending on how depleted your battery was, it could take several hours to fully charge it up again.
Once the charger indicates that the battery is fully charged, disconnect the leads in reverse order (negative first, then positive), and put everything away. Try starting your Terrain again – if all goes well, it should fire right up!
Credit: www.mcguireautogroup.net
How Do You Jump a Battery in a 2014 Gmc Terrain?
If your 2014 GMC Terrain has a dead battery, you’ll need to jumpstart it. Here’s how:
1. Park the good car next to the Terrain and turn off both engines.
2. Open the hoods and locate the batteries. On the Terrain, the battery is on the driver’s side.
3. Connect one end of the positive (red) jumper cable to the positive terminal of the dead battery. Then connect the other end of the positive jumper cable to the positive terminal of the good battery.
4. Connect one end of the negative (black) jumper cable to the negative terminal of the good battery.
Where Do You Connect the Cables to Jump Start?
Most vehicles have the battery located under the hood, so you’ll need to open the hood and locate it before you can jump start the car. Once you’ve found it, identify the positive and negative terminals. The positive terminal is usually larger than the negative terminal and is labeled with a “+” sign.
The negative terminal is usually labeled with a “-” sign.
Attach one end of the red jumper cable to the positive terminal of the dead battery, and then attach the other end of the red jumper cable to the positive terminal of the good battery. Next, attach one end of the black jumper cable to the negative terminal of the good battery, and then attach the other end of black jumper cable to an unpainted metal surface on your vehicle that is away from any moving parts (this will serve as a grounding point).
Once all four cables are attached, have someone start up the working vehicle while you try to start up your vehicle. If done correctly, your car should start right up!
Where Do You Put the Negative Cable When Jump Starting?
When you jump start a car, the negative cable always goes on the metal part of the car that is not painted. This could be a bolt or some other metal protrusion. You want to make sure that the clamp on the negative cable has a good connection with bare metal so there is no risk of electrical fires.
Do You Put the Positive Or Negative Jumper Cable on First?
If you’re jump starting a car, the process is simple. But it’s important to do it in the right order to avoid damaging your car’s electrical system. First, connect one end of the positive jumper cable to the positive terminal of the dead battery.
Then, connect the other end of the positive cable to the live battery. Next, connect one end of the negative cable to the negative terminal of the live battery. Finally, connect the other end of the negative cable to a metal part of the dead car that isn’t connected to anything else – like a bolt on an engine block.