The amount of air you should put in your air shocks will depend on the weight of your vehicle and how much support you need. A good rule of thumb is to start with around 25-30 PSI and adjust from there.
Do you have air shocks on your car or truck? If so, you might be wondering how much air to put in them.
The answer can vary depending on the vehicle and the desired ride quality.
However, as a general rule of thumb, most people will add about 2-3 PSI per corner. So, if you have a 4-wheel vehicle with air shocks, you would add 8-12 PSI to the system.
Of course, it’s always best to consult your owner’s manual or an expert before making any changes to your vehicle.
But following this simple guideline should help you get started in finding the perfect air pressure for your air shocks!
What is the Max Psi for Air Shocks
Air shocks are a type of shock absorber that uses air pressure to cushion the ride. They are often used in off-road vehicles and race cars, as they can provide a smoother ride over rough terrain. The amount of air pressure inside the shocks can be adjusted to suit the needs of the driver.
The maximum psi for air shocks varies depending on the make and model of the vehicle. However, most air shocks have a maximum psi between 100 and 200. This means that they can withstand a lot of pressure before they start to leak or fail.
If you are planning on using your vehicle in off-road conditions, it is important to check the maximum psi rating of your air shocks before heading out. This will ensure that they are able to cope with the demands of driving on rough terrain.
Credit: www.topeak.com
How Much Pressure Should I Put in My Shock?
This is a difficult question to answer because it depends on many factors, such as the type of shock you have, the terrain you’re riding on, and your personal preferences. That said, here are some general guidelines:
If you have an air-sprung shock, start by setting the air pressure to the recommended level for your weight.
You can find this information in the shock’s owner’s manual. Once you have the air pressure set, you can fine-tune it by adjusting the rebound damping. If the rebound is too slow, the bike will feel sluggish; if it’s too fast, the bike will feel bouncy.
If you have a coil-sprung shock, start by setting the preload to your weight. Again, you can find this information in the shock’s owner’s manual. Once you have the preload set, you can fine-tune it by adjusting both the compression and rebound damping.
As with air shocks, if either of these is set too low, the bike will feel sluggish; if either is set too high,the bike will feel bouncy.
How Do You Add Air to an Air Shock?
If your air shock is low on air, you can add more using a shock pump. First, remove the valve cap and press the release button to let any air out of the Schrader valve. Then, attach the pump to the valve and start pumping.
You’ll know when the shock is full when resistance from the pump stops increasing. Finally, put the valve cap back on and test your shock by bouncing up and down on it.
How Many Psi Can Air Shocks Hold?
The maximum amount of air pressure that can be held in an air shock is determined by the size of the air chamber. Most air shocks will have a maximum pressure rating of 200-psi. Some larger volume air shocks may have a maximum pressure rating as high as 350-psi.
How Much Air Should I Put in My Rear Shock?
This is a great question and one that we get asked a lot. The answer, unfortunately, isn’t as straightforward as we would like it to be. It depends on a few different factors such as:
-The weight of the rider
-The type of terrain you’ll be riding on
-Your personal preferences
With that being said, there are some general guidelines you can follow. If you’re a lighter rider (under 150lbs), start with around 50-60psi in your rear shock. If you’re a heavier rider (over 200lbs), start with around 60-70psi.
And if you’re somewhere in between, start with around 55-65psi.
Keep in mind that these are just starting points and you may need to experiment a bit to find what feels best for you. Also, remember to check your pressure regularly and adjust as needed – especially if you notice your bike feeling softer than usual or if you’ve been riding in particularly rough conditions.
Easiest Way To Add Air To MTB Fork And Shocks
Conclusion
You may have noticed that your air shocks seem to be leaking air. You may be wondering how much air you should put in them. Here is a quick guide on how much air to put in your air shocks.
The amount of air that you put in your shocks will depend on the weight of your vehicle. If you have a light car, you will need less air than if you have a heavy truck. You can usually find the recommended amount of air for your shocks in the owner’s manual for your vehicle.
If you don’t have the owner’s manual, or if you are unsure about how much air to put in, start with 30 psi (pounds per square inch). This is a good starting point for most vehicles. If your shocks are still too soft, add more air until they feel firm but not hard.
Remember, it is better to err on the side of too much air rather than too little.
Putting too little air in your shocks can cause them to bottom out, which can damage both the shocks and the suspension components of your vehicle. So when in doubt, add more air!